Design and Fabrication of Printed DNA Droplets Arrangement and Detection Inkjet System

研究成果: 書貢獻/報告類型章節

摘要

This article describes the aims to establish a thermal bubble printhead with simultaneously driving multi-channel for DNA droplet arrangement. It proposed a monolithic CMOS/MEMS system with multi-level output voltage ESD protection system for protected inkjet printhead. High-voltage power, low-voltage logic, and CMOS/MEMS architecture were integrated in inkjet chip. It used bulk micromachining technology (MEMS). On-chip high-voltage electrostatic discharge (HV-ESD), protection design in smart power technology of monolithic inkjet chip is a challenging issue. The nozzle jets interleaving scanning sequence is controlled spatially on the elements to avoid the strong interference with DNA droplets caused by the excitation of the neighbor driven elements. A heating element, disposed on the substrate, includes a conductor loop which does not encompass the heating elements on the substrate. The configuration of the heater jet significantly reduces both electromagnetic and capacitance interference caused by the heating elements. The simulation and experience result have shown in the research. It is reduced nearly half the time compared to the case with traditional scanning sequence. This experiment develops new controlled structure designs of chip for inkjet printheads. A bubble inkjet(TIJ) device is designed, several of the architectures may be adjusted just a small microns to improve and optimize the DNA drop nucleation and generation efficiency. The DNA droplet ejection behavior of the multiplexer inkjet printhead within 60-μm orifice size has been measured beyond 5 kHz operation system, 12 pL capacity of ejected DNA droplet volume.
原文英語
主出版物標題Printed Electronics - Current Trends and Applications
編輯Ilgu Yun
出版地Rijeka
發行者InTech
DOIs
出版狀態已發佈 - 九月 28 2016

指紋

DNA
Electric heating elements
Fabrication
MEMS
Electric potential
Scanning
Electrostatic discharge
Micromachining
Substrates
Orifices
Nozzles
Nucleation
Capacitance
Experiments

引用此文

Liou, J-C. (2016). Design and Fabrication of Printed DNA Droplets Arrangement and Detection Inkjet System. 於 I. Yun (編輯), Printed Electronics - Current Trends and Applications Rijeka: InTech. https://doi.org/10.5772/63329

Design and Fabrication of Printed DNA Droplets Arrangement and Detection Inkjet System. / Liou, Jian-Chiun.

Printed Electronics - Current Trends and Applications. 編輯 / Ilgu Yun. Rijeka : InTech, 2016.

研究成果: 書貢獻/報告類型章節

Liou, J-C 2016, Design and Fabrication of Printed DNA Droplets Arrangement and Detection Inkjet System. 於 I Yun (編輯), Printed Electronics - Current Trends and Applications. InTech, Rijeka. https://doi.org/10.5772/63329
Liou J-C. Design and Fabrication of Printed DNA Droplets Arrangement and Detection Inkjet System. 於 Yun I, 編輯, Printed Electronics - Current Trends and Applications. Rijeka: InTech. 2016 https://doi.org/10.5772/63329
Liou, Jian-Chiun. / Design and Fabrication of Printed DNA Droplets Arrangement and Detection Inkjet System. Printed Electronics - Current Trends and Applications. 編輯 / Ilgu Yun. Rijeka : InTech, 2016.
@inbook{7992257545c84963a184b4f2ffc96546,
title = "Design and Fabrication of Printed DNA Droplets Arrangement and Detection Inkjet System",
abstract = "This article describes the aims to establish a thermal bubble printhead with simultaneously driving multi-channel for DNA droplet arrangement. It proposed a monolithic CMOS/MEMS system with multi-level output voltage ESD protection system for protected inkjet printhead. High-voltage power, low-voltage logic, and CMOS/MEMS architecture were integrated in inkjet chip. It used bulk micromachining technology (MEMS). On-chip high-voltage electrostatic discharge (HV-ESD), protection design in smart power technology of monolithic inkjet chip is a challenging issue. The nozzle jets interleaving scanning sequence is controlled spatially on the elements to avoid the strong interference with DNA droplets caused by the excitation of the neighbor driven elements. A heating element, disposed on the substrate, includes a conductor loop which does not encompass the heating elements on the substrate. The configuration of the heater jet significantly reduces both electromagnetic and capacitance interference caused by the heating elements. The simulation and experience result have shown in the research. It is reduced nearly half the time compared to the case with traditional scanning sequence. This experiment develops new controlled structure designs of chip for inkjet printheads. A bubble inkjet(TIJ) device is designed, several of the architectures may be adjusted just a small microns to improve and optimize the DNA drop nucleation and generation efficiency. The DNA droplet ejection behavior of the multiplexer inkjet printhead within 60-μm orifice size has been measured beyond 5 kHz operation system, 12 pL capacity of ejected DNA droplet volume.",
author = "Jian-Chiun Liou",
year = "2016",
month = "9",
day = "28",
doi = "10.5772/63329",
language = "English",
editor = "Ilgu Yun",
booktitle = "Printed Electronics - Current Trends and Applications",
publisher = "InTech",
address = "Croatia",

}

TY - CHAP

T1 - Design and Fabrication of Printed DNA Droplets Arrangement and Detection Inkjet System

AU - Liou, Jian-Chiun

PY - 2016/9/28

Y1 - 2016/9/28

N2 - This article describes the aims to establish a thermal bubble printhead with simultaneously driving multi-channel for DNA droplet arrangement. It proposed a monolithic CMOS/MEMS system with multi-level output voltage ESD protection system for protected inkjet printhead. High-voltage power, low-voltage logic, and CMOS/MEMS architecture were integrated in inkjet chip. It used bulk micromachining technology (MEMS). On-chip high-voltage electrostatic discharge (HV-ESD), protection design in smart power technology of monolithic inkjet chip is a challenging issue. The nozzle jets interleaving scanning sequence is controlled spatially on the elements to avoid the strong interference with DNA droplets caused by the excitation of the neighbor driven elements. A heating element, disposed on the substrate, includes a conductor loop which does not encompass the heating elements on the substrate. The configuration of the heater jet significantly reduces both electromagnetic and capacitance interference caused by the heating elements. The simulation and experience result have shown in the research. It is reduced nearly half the time compared to the case with traditional scanning sequence. This experiment develops new controlled structure designs of chip for inkjet printheads. A bubble inkjet(TIJ) device is designed, several of the architectures may be adjusted just a small microns to improve and optimize the DNA drop nucleation and generation efficiency. The DNA droplet ejection behavior of the multiplexer inkjet printhead within 60-μm orifice size has been measured beyond 5 kHz operation system, 12 pL capacity of ejected DNA droplet volume.

AB - This article describes the aims to establish a thermal bubble printhead with simultaneously driving multi-channel for DNA droplet arrangement. It proposed a monolithic CMOS/MEMS system with multi-level output voltage ESD protection system for protected inkjet printhead. High-voltage power, low-voltage logic, and CMOS/MEMS architecture were integrated in inkjet chip. It used bulk micromachining technology (MEMS). On-chip high-voltage electrostatic discharge (HV-ESD), protection design in smart power technology of monolithic inkjet chip is a challenging issue. The nozzle jets interleaving scanning sequence is controlled spatially on the elements to avoid the strong interference with DNA droplets caused by the excitation of the neighbor driven elements. A heating element, disposed on the substrate, includes a conductor loop which does not encompass the heating elements on the substrate. The configuration of the heater jet significantly reduces both electromagnetic and capacitance interference caused by the heating elements. The simulation and experience result have shown in the research. It is reduced nearly half the time compared to the case with traditional scanning sequence. This experiment develops new controlled structure designs of chip for inkjet printheads. A bubble inkjet(TIJ) device is designed, several of the architectures may be adjusted just a small microns to improve and optimize the DNA drop nucleation and generation efficiency. The DNA droplet ejection behavior of the multiplexer inkjet printhead within 60-μm orifice size has been measured beyond 5 kHz operation system, 12 pL capacity of ejected DNA droplet volume.

U2 - 10.5772/63329

DO - 10.5772/63329

M3 - Chapter

BT - Printed Electronics - Current Trends and Applications

A2 - Yun, Ilgu

PB - InTech

CY - Rijeka

ER -