Lower power supply thermal bubble printhead chip with MEMS technology increasing thermal energy effect

Jian Chiun Liou, Chun Jung Chen, Min Hon Chuang

Research output: Chapter in Book/Report/Conference proceedingConference contribution

1 Citation (Scopus)

Abstract

This paper describes the low power supply aimed to develop a thermal inkjet(TIJ) printhead by using bulk micromachining technology (MEMS). This experiment develops new structure designs of chip for inkjet printheads. A thermal inkjet device is designed, several of the dimensions may be adjusted just a few microns to change or optimize the drop generation performance. This energy conversion devices and systems based on Integrated Driver Head with The Performance of High-Frequency And Picoliter Drop Inkjet and structures. The TIJ process is akin to an internal combustion engine driven by an explosive phase change rather than an oxidation. In cooking, boiling is experienced as a process with an unpredictable beginning, following the lighting of the cooking flame. The boiling process is given its essential predictability in TIJ by using very great power densities to superheat the fluid far above its normal boiling temperature. Some of the waste heat can be carried away by silicon substrate. That is, the heater has excellent heat capacity. Deciding it to warm a few degrees by taking up waste heat at a location away from the heater region can significantly assist the heat management problem. For thermal inkjet printhead, the back side etching is used. The technology of microelectro-mechanical system to achieve a better thermal isolation structure and minimize conductive heat losses. Controling energy conversion is important. The fabricated back side etching thermal inkjet (TIJ) printhead is measured by open pool and close pool system. The measured begin voltage is 6.5 V, Life time is 9×10̂7.

Original languageEnglish
Title of host publicationFinal Program and Proceedings of IS and T's NIP20
Subtitle of host publicationInternational Conference on Digital Printing Technologies
Pages863-866
Number of pages4
Publication statusPublished - 2004
Externally publishedYes
EventFinal Program and Proceedings of IS and T's NIP20: International Conference on Digital Printing Technologies - Salt Lake City, UT, United States
Duration: Oct 31 2004Nov 5 2004

Conference

ConferenceFinal Program and Proceedings of IS and T's NIP20: International Conference on Digital Printing Technologies
CountryUnited States
CitySalt Lake City, UT
Period10/31/0411/5/04

Fingerprint

Thermal energy
MEMS
Boiling liquids
Waste heat
Cooking
Energy conversion
Etching
Hot Temperature
Micromachining
Internal combustion engines
Heat losses
Specific heat
Lighting
Silicon
Oxidation
Fluids
Electric potential
Substrates

ASJC Scopus subject areas

  • Media Technology
  • Computer Science Applications

Cite this

Liou, J. C., Chen, C. J., & Chuang, M. H. (2004). Lower power supply thermal bubble printhead chip with MEMS technology increasing thermal energy effect. In Final Program and Proceedings of IS and T's NIP20: International Conference on Digital Printing Technologies (pp. 863-866)

Lower power supply thermal bubble printhead chip with MEMS technology increasing thermal energy effect. / Liou, Jian Chiun; Chen, Chun Jung; Chuang, Min Hon.

Final Program and Proceedings of IS and T's NIP20: International Conference on Digital Printing Technologies. 2004. p. 863-866.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Liou, JC, Chen, CJ & Chuang, MH 2004, Lower power supply thermal bubble printhead chip with MEMS technology increasing thermal energy effect. in Final Program and Proceedings of IS and T's NIP20: International Conference on Digital Printing Technologies. pp. 863-866, Final Program and Proceedings of IS and T's NIP20: International Conference on Digital Printing Technologies, Salt Lake City, UT, United States, 10/31/04.
Liou JC, Chen CJ, Chuang MH. Lower power supply thermal bubble printhead chip with MEMS technology increasing thermal energy effect. In Final Program and Proceedings of IS and T's NIP20: International Conference on Digital Printing Technologies. 2004. p. 863-866
Liou, Jian Chiun ; Chen, Chun Jung ; Chuang, Min Hon. / Lower power supply thermal bubble printhead chip with MEMS technology increasing thermal energy effect. Final Program and Proceedings of IS and T's NIP20: International Conference on Digital Printing Technologies. 2004. pp. 863-866
@inproceedings{ffab1b63b00047d2ba4573d90d0b2cc7,
title = "Lower power supply thermal bubble printhead chip with MEMS technology increasing thermal energy effect",
abstract = "This paper describes the low power supply aimed to develop a thermal inkjet(TIJ) printhead by using bulk micromachining technology (MEMS). This experiment develops new structure designs of chip for inkjet printheads. A thermal inkjet device is designed, several of the dimensions may be adjusted just a few microns to change or optimize the drop generation performance. This energy conversion devices and systems based on Integrated Driver Head with The Performance of High-Frequency And Picoliter Drop Inkjet and structures. The TIJ process is akin to an internal combustion engine driven by an explosive phase change rather than an oxidation. In cooking, boiling is experienced as a process with an unpredictable beginning, following the lighting of the cooking flame. The boiling process is given its essential predictability in TIJ by using very great power densities to superheat the fluid far above its normal boiling temperature. Some of the waste heat can be carried away by silicon substrate. That is, the heater has excellent heat capacity. Deciding it to warm a few degrees by taking up waste heat at a location away from the heater region can significantly assist the heat management problem. For thermal inkjet printhead, the back side etching is used. The technology of microelectro-mechanical system to achieve a better thermal isolation structure and minimize conductive heat losses. Controling energy conversion is important. The fabricated back side etching thermal inkjet (TIJ) printhead is measured by open pool and close pool system. The measured begin voltage is 6.5 V, Life time is 9×10̂7.",
author = "Liou, {Jian Chiun} and Chen, {Chun Jung} and Chuang, {Min Hon}",
year = "2004",
language = "English",
pages = "863--866",
booktitle = "Final Program and Proceedings of IS and T's NIP20",

}

TY - GEN

T1 - Lower power supply thermal bubble printhead chip with MEMS technology increasing thermal energy effect

AU - Liou, Jian Chiun

AU - Chen, Chun Jung

AU - Chuang, Min Hon

PY - 2004

Y1 - 2004

N2 - This paper describes the low power supply aimed to develop a thermal inkjet(TIJ) printhead by using bulk micromachining technology (MEMS). This experiment develops new structure designs of chip for inkjet printheads. A thermal inkjet device is designed, several of the dimensions may be adjusted just a few microns to change or optimize the drop generation performance. This energy conversion devices and systems based on Integrated Driver Head with The Performance of High-Frequency And Picoliter Drop Inkjet and structures. The TIJ process is akin to an internal combustion engine driven by an explosive phase change rather than an oxidation. In cooking, boiling is experienced as a process with an unpredictable beginning, following the lighting of the cooking flame. The boiling process is given its essential predictability in TIJ by using very great power densities to superheat the fluid far above its normal boiling temperature. Some of the waste heat can be carried away by silicon substrate. That is, the heater has excellent heat capacity. Deciding it to warm a few degrees by taking up waste heat at a location away from the heater region can significantly assist the heat management problem. For thermal inkjet printhead, the back side etching is used. The technology of microelectro-mechanical system to achieve a better thermal isolation structure and minimize conductive heat losses. Controling energy conversion is important. The fabricated back side etching thermal inkjet (TIJ) printhead is measured by open pool and close pool system. The measured begin voltage is 6.5 V, Life time is 9×10̂7.

AB - This paper describes the low power supply aimed to develop a thermal inkjet(TIJ) printhead by using bulk micromachining technology (MEMS). This experiment develops new structure designs of chip for inkjet printheads. A thermal inkjet device is designed, several of the dimensions may be adjusted just a few microns to change or optimize the drop generation performance. This energy conversion devices and systems based on Integrated Driver Head with The Performance of High-Frequency And Picoliter Drop Inkjet and structures. The TIJ process is akin to an internal combustion engine driven by an explosive phase change rather than an oxidation. In cooking, boiling is experienced as a process with an unpredictable beginning, following the lighting of the cooking flame. The boiling process is given its essential predictability in TIJ by using very great power densities to superheat the fluid far above its normal boiling temperature. Some of the waste heat can be carried away by silicon substrate. That is, the heater has excellent heat capacity. Deciding it to warm a few degrees by taking up waste heat at a location away from the heater region can significantly assist the heat management problem. For thermal inkjet printhead, the back side etching is used. The technology of microelectro-mechanical system to achieve a better thermal isolation structure and minimize conductive heat losses. Controling energy conversion is important. The fabricated back side etching thermal inkjet (TIJ) printhead is measured by open pool and close pool system. The measured begin voltage is 6.5 V, Life time is 9×10̂7.

UR - http://www.scopus.com/inward/record.url?scp=14244250354&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=14244250354&partnerID=8YFLogxK

M3 - Conference contribution

AN - SCOPUS:14244250354

SP - 863

EP - 866

BT - Final Program and Proceedings of IS and T's NIP20

ER -