Extension method and numerical simulation of micro-injection molding

Y.K. Shen, Y.J. Shie, W.Y. Wu

Research output: Contribution to journalArticle

19 Citations (Scopus)

Abstract

Micro system technology is including Optic, Mechanism, Electricity, Material, Control and Chemistry, etc. Micro-injection molding is a branch of micro system technology. In this study, 3D numerical simulation and extension method are performed on micro-injection molding. The analysis with different polymers (such as PP ? PA and POM) ? processing parameters (injection time ? mold temperature ? injection temperature ? injection temperature and injection pressure) uses to simulate the micro-gear for example. In order to obtain optimum result, the analysis introduces Taguchi method to discuss the influence of each parameter in micro-injection molding. In this study, the results between numerical simulation and extension method show that the mold temperature is the most important factor on processing parameters and PP material is the best suitable material. © 2004 Elsevier Science Ltd.
Original languageEnglish
Pages (from-to)795-804
Number of pages10
JournalInternational Communications in Heat and Mass Transfer
Volume31
Issue number6
DOIs
Publication statusPublished - 2004

Fingerprint

injection molding
Injection molding
injection
Computer simulation
simulation
Taguchi methods
Temperature
temperature
Processing
electricity
Gears
Optics
Polymers
Electricity
optics
chemistry
polymers

Cite this

Extension method and numerical simulation of micro-injection molding. / Shen, Y.K.; Shie, Y.J.; Wu, W.Y.

In: International Communications in Heat and Mass Transfer, Vol. 31, No. 6, 2004, p. 795-804.

Research output: Contribution to journalArticle

@article{a062f01ced174abdbdf30bcf640d65e0,
title = "Extension method and numerical simulation of micro-injection molding",
abstract = "Micro system technology is including Optic, Mechanism, Electricity, Material, Control and Chemistry, etc. Micro-injection molding is a branch of micro system technology. In this study, 3D numerical simulation and extension method are performed on micro-injection molding. The analysis with different polymers (such as PP ? PA and POM) ? processing parameters (injection time ? mold temperature ? injection temperature ? injection temperature and injection pressure) uses to simulate the micro-gear for example. In order to obtain optimum result, the analysis introduces Taguchi method to discuss the influence of each parameter in micro-injection molding. In this study, the results between numerical simulation and extension method show that the mold temperature is the most important factor on processing parameters and PP material is the best suitable material. {\circledC} 2004 Elsevier Science Ltd.",
author = "Y.K. Shen and Y.J. Shie and W.Y. Wu",
year = "2004",
doi = "10.1016/S0735-1933",
language = "English",
volume = "31",
pages = "795--804",
journal = "International Communications in Heat and Mass Transfer",
issn = "0735-1933",
publisher = "Elsevier Limited",
number = "6",

}

TY - JOUR

T1 - Extension method and numerical simulation of micro-injection molding

AU - Shen, Y.K.

AU - Shie, Y.J.

AU - Wu, W.Y.

PY - 2004

Y1 - 2004

N2 - Micro system technology is including Optic, Mechanism, Electricity, Material, Control and Chemistry, etc. Micro-injection molding is a branch of micro system technology. In this study, 3D numerical simulation and extension method are performed on micro-injection molding. The analysis with different polymers (such as PP ? PA and POM) ? processing parameters (injection time ? mold temperature ? injection temperature ? injection temperature and injection pressure) uses to simulate the micro-gear for example. In order to obtain optimum result, the analysis introduces Taguchi method to discuss the influence of each parameter in micro-injection molding. In this study, the results between numerical simulation and extension method show that the mold temperature is the most important factor on processing parameters and PP material is the best suitable material. © 2004 Elsevier Science Ltd.

AB - Micro system technology is including Optic, Mechanism, Electricity, Material, Control and Chemistry, etc. Micro-injection molding is a branch of micro system technology. In this study, 3D numerical simulation and extension method are performed on micro-injection molding. The analysis with different polymers (such as PP ? PA and POM) ? processing parameters (injection time ? mold temperature ? injection temperature ? injection temperature and injection pressure) uses to simulate the micro-gear for example. In order to obtain optimum result, the analysis introduces Taguchi method to discuss the influence of each parameter in micro-injection molding. In this study, the results between numerical simulation and extension method show that the mold temperature is the most important factor on processing parameters and PP material is the best suitable material. © 2004 Elsevier Science Ltd.

UR - https://www.scopus.com/record/display.uri?eid=2-s2.0-2442456606&origin=resultslist&sort=plf-f&src=s&st1=Extension+method+and+numerical+simulation+of+micro-injection+molding&st2=&sid=9b8bac3b06f6059926bc490032eda544&sot=b&sdt=b&sl=83&s=TITLE-ABS-KEY%28Extension+method+and+numerical+simulation+of+micro-injection+molding%29&relpos=1&citeCnt=19&searchTerm=

UR - https://www.scopus.com/results/citedbyresults.uri?sort=plf-f&cite=2-s2.0-2442456606&src=s&imp=t&sid=f94327b6bcb2ca92d6d207e086d0931e&sot=cite&sdt=a&sl=0&origin=recordpage&editSaveSearch=&txGid=4645a83693648e0bf799b3c3dc185176

U2 - 10.1016/S0735-1933

DO - 10.1016/S0735-1933

M3 - Article

VL - 31

SP - 795

EP - 804

JO - International Communications in Heat and Mass Transfer

JF - International Communications in Heat and Mass Transfer

SN - 0735-1933

IS - 6

ER -